MICRO SEVEN, INCâ MODEL RT15
Micro
Seven, Inc.
P.O.
Box 5597
Beaverton,
OR
97006
U.S.A.
phone:
503-693-6982
fax:
503-693-9742
e-mail:
support@microseveninc.com
Copyright, Ó2007
by Micro Seven, Inc. All right reserved.
INTRODUCTION
Micro Seven model RT15,
Telephone-Call Router uses a single "3-way" or "Conference
Call" featured telephone line to transfer or divert telephone calls
between telephone lines. Entering PIN is no longer needed because RT15 reads
caller's telephone number from caller-ID delivery feature that is available
from telephone company. When a caller wants to place a call, the caller dials a
local telephone number that is assigned to RT15. When the line is ringing two
times, the caller hangs up the call. Few seconds later, RT15 calls back the
caller if the caller's telephone number is registered with RT15 memory. When
the caller answers the call from RT15, the caller hears a prompt tone. The
caller dials a final telephone number that includes "1" and ten digit
number. RT15 flash-hooks the line, and RT15 flash hooks the line. It obtains
dial tone, and it dials the telephone number that is received. When the called
line answers the call, RT15 flash-hooks the line to connect the original caller
and the answered caller. Few seconds later, RT15 hangs up the call to end the
sequence. Then RT15 is ready to receive another call.
SPECIFICATIONS
Telephone
number storage:
RT15 reads telephone number from received caller-ID
data, and it compares with telephone numbers that are stored in RT15. The
standard storage size of telephone number is two thousands, and it may be
expanded to maximum fifty thousand telephone numbers by increasing memory size
in RT15. Loading new telephone numbers into RT15 requires using provided
control software.
Caller-ID
formats:
RT15 is compatible with Bellcore and ETS caller-ID
standards, and it accepts caller-ID delivery between ring signal for both
multiple-message and single-message formats.
Control
software:
Window-type control software is provided to enter
telephone number into RT15.
Front-panel
indicators:
1.
CID Match: LED flashes with RT15 received a matched
telephone number as a caller-ID parameter from telephone company with a
registered telephone number in RT15.
2.
Ring indicator/Loop current. It turns on when RT15
receives ring signal and when there is loop current (off-hook).
Rear
panel controls:
1.
RS232 connector
2.
Telephone connector
3.
Power indicator (green LED)
4.
Power input (+12V)
AC/DC
Adapter: 117VAC +/- 5%, or 230VAC +/- 5%(for optional 230V
AC/DC Adapter)
DC
input: 12VDC unregulated, 100mA maximum
Calibration:
not required
Dimensions:
19 cm (4") W x 4.5 cm (1.75") H x 10 cm (7.5") L
Weight: 400g (0.8 lbs.)
Environmental:
Operating temperature: 0 to 35 degree C, Humidity: 85% RH at 35 degree C
Warranty/Service: 6
months limited warranty. No warranty if any factory seal is broken. Service is
performed at the factory, usually within 5 working days.
Country
of Origin: Manufactured in United States of America
OPERATING PROCEDURES
By using another telephone line like cell phone,
dialing a telephone number that is assigned to RT15 and call RT15. You hear
telephone line is ringing (ring-back tone), and ring indicator on RT15 front
panel is turned on and off. If your other telephone number is stored in RT15
memory, "CID MATCH" LED indicator on RT15 front panel is turned on
for two seconds. Hang up your cell phone.
RT15
call back
After five seconds, RT15 turns on off-hook relay, and
Ring signal/off-hook indicator on RT15 front panel is turned on. RT15 is
dialing your telephone number. You will hear your cell phone ringing. Answer
the call by saying "Hello" loudly. Then you will hear a prompt tone
like "beep" "beep" "beep" for asking telephone
number entry. If you do not say "Hello" loudly, you will hear the
prompt tone within few seconds.
Dialing
telephone number
Dial a final telephone number that you want to call.
Maximum time between digits is about seven seconds. If you made a mistake
dialing, dial "#" to cancel to go back to the beginning of telephone
number. Long-distance telephone number that starts with "1" is
recognized quickly and any telephone number like local calls and international
number takes few more seconds before RT15's next action.
RT15
dialing again
RT15 flash-hooks the telephone line to connect to
other line, dials the received final telephone number.
Destination
telephone set is ringing and RT15 hangs up
A destination telephone set is ringing, and when the
line is answered, RT15 flash-hooks to connect you and the called party. You
will be able to observe the flash-hook actions on RT15 front panel LED also.
Then RT15 hangs up the line, and you will see the LED turned off.